052-6411 rev a 2-2013 APT70GR120B2_l symbol parameter ratings unit v ces collector emitter voltage 1200 v v ge gate-emitter voltage 30 i c1 continuous collector current @ t c = 25c 160 a i c2 continuous collector current @ t c = 110c 70 i cm pulsed collector current 1 280 scwt short circuit withstand time: v ce = 600v, v ge = 15v, t c =125c 10 s p d total power dissipation @ t c = 25c 961 w t j ,t stg operating and storage junction temperature range -55 to 150 c t l max. lead temp. for soldering: 0.063" from case for 10 sec. 300 maximum ratings all ratings: t c = 25c unless otherwise speciied. static electrical characteristics microsemi website - http://www.microsemi.com caution: these devices are sensitive to electrostatic discharge. proper handling procedures should be followed. symbol parameter min typ max unit v (br)ces collector-emitter breakdown voltage (v ge = 0v, i c = 1.0ma) 1200 volts v ge(th) gate threshold voltage (v ce = v ge , i c = 2.5ma, t j = 25c) 3.5 5.0 6.5 v ce(on) collector-emitter on voltage (v ge = 15v, i c = 70a, t j = 25c) 2.5 3.2 collector-emitter on voltage (v ge = 15v, i c = 70a, t j = 125c) 3.3 collector-emitter on voltage (v ge = 15v, i c = 140a, t j = 25c) 3.5 i ces collector cut-off current (v ce = 1200v, v ge = 0v, t j = 25c) 2 10 1000 a collector cut-off current (v ce = 1200v, v ge = 0v, t j = 125c) 2 100 i ges gate-emitter leakage current (v ge = 20v) 250 na ultra fast npt - igbt ? the ultra fast npt - igbt ? is a new generation of high voltage power igbts. using non-punch-through technology, the ultra fast npt-igbt ? offers superior ruggedness and ultrafast switching speed. features ? low saturation voltage ? low tail current ? rohs compliant ? short circuit withstand rated ? high frequency switching ? ultra low leakage current unless stated otherwise, microsemi discrete igbts contain a single igbt die. this device is recommended for applications such as induction heating (ih), motor control, general purpose inverters and uninterruptible power supplies (ups). APT70GR120B2 apt70gr120l 1200v, 70a, v ce(on) = 2.5v typical downloaded from: http:///
APT70GR120B2_l 052-6411 rev a 2-2013 thermal and mechanical characteristics dynamic characteristics symbol characteristic min typ max unit r jc junction to case thermal resistance (igbt) .13 c/w r ja junction to ambient thermal resistance 40 w t package weight b2 .22 oz 6 g l .36 oz 10 g 1 repetitive rating: pulse width and case temperature limited by maximum junction temperature. 2 pulse test: pulse width < 380 s , duty cycle < 2%. 3 see mil-std-750 method 3471.4 r g is external gate resistance, not including internal gate resistance or gate driver impedance. (mic4452) 5 e on2 is the clamped inductive turn on energy that includes a commutating diode reverse recovery current in the igbt turn on energy loss. a combi device is used for the clamping diode.6 e off is the clamped inductive turn-off energy measured in accordance with jedec standard jesd24-1. microsemi reserves the right to change, without notice, the speciications and information contained herein. symbol parameter test conditions min typ max unit c ies input capacitance capacitance v ge = 0v, v ce = 25v f = 1mhz 7260 pf c oes output capacitance 643 c res reverse transfer capacitance 199 v gep gate to emitter plateau voltage gate charge v ge = 15v v ce = 600v i c = 70a 7.5 v q g 3 total gate charge 412 544 nc q ge gate-emitter charge 48 62 q gc gate- collector charge 204 275 t d(on) turn-on delay time inductive switching (25c) v cc = 600v v ge = 15v i c = 70a r g = 4.3 4 t j = +25c 33 ns t r current rise time 48 t d(off) turn-off delay time 278 t f current fall time 64 e on2 5 turn-on switching energy 3816 5720 j e off 6 turn-off switching energy 2582 3870 t d(on) turn-on delay time inductive switching (125c) v cc = 600v v ge = 15v i c = 70a r g = 4.3 4 t j = +125c 33 ns t r current rise time 48 t d(off) turn-off delay time 320 t f current fall time 74 e on2 5 turn-on switching energy 5651 8475 j e off 6 turn-off switching energy 3323 4980 0 0.02 0.04 0.06 0.08 0.10 0.12 0.14 10 -4 10 -3 10 -2 0.1 1 10 10 -5 z jc , thermal impedance (c/w) 0.3 d = 0.9 0.7 single pulse rectangular pulse duration (seconds) figure 1, maximum effective transient thermal impedance, junction-to-case vs pulse duration 0.5 0.1 0.05 peak t j = p dm x z jc + t c duty factor d = t 1 / t 2 t 2 t 1 p dm note : downloaded from: http:///
052-6411 rev a 2-2013 APT70GR120B2_l typical performance curves 0 50 100 150 200 250 -50 -25 0 25 50 75 100 125 150 0 1 2 3 4 5 6 -50 0 50 100 150 0 1 2 3 4 5 6 6 8 10 12 14 16 0 50 100 150 200 250 0 2 4 6 8 10 12 0 50 100 150 200 250 300 0 4 8 12 16 20 24 28 32 0 50 100 150 200 0 2 4 6 8 10 250s pulse test<0.5 % duty cycle t j = 25c. 250s pulse test <0.5 % duty cycle v ge = 15v. 250s pulse test <0.5 % duty cycle i c = 35a i c = 70a i c = 140a i c = 70a i c = 140a 13v 15v t j = 25c t j = -55c v ge = 15v t j = - 55c t j = 150c v ce , collector-to-emitter voltage (v) figure 3, saturation voltage characteristics (t j = 25c) i c , collector current (a) t j = 25c t j = 125c v ce , collector-to-emitter voltage (v) figure 4, output characteristics (t j = 25c) i c , collector current (a) t j = 125c v ge , gate-to-emitter voltage (v) figure 6, transfer characteristics i c , collector current (a) v ge , gate-to-emitter voltage (v) figure 7, on state voltage vs gate-to-emitter voltage v ce , collector-to-emitter voltage (v) t j , junction temperature (c) figure 5, on state voltage vs junction temperature v ce , collector-to-emitter voltage (v) t c , case temperature (c) figure 9, dc collector current vs case temperature i c , dc collector current (a) 0.80 0.85 0.90 0.95 1.00 1.05 1.10 1.15 1.20 - 50 -25 0 25 50 75 100 125 t j , junction temperature figure 8, threshold voltage vs junction temperature v gs(th) , threshold voltage (normalized) 6.5v 7v i c = 35a 8.0v 9.0v 7.5v i c (a) figure 2, max frequency vs current (t case = 75c) t j = 150c 0 20 40 60 80 100 120 140 0 25 50 75 100 125 150 frequency (khz) 8.5v downloaded from: http:///
APT70GR120B2_l 052-6411 rev a 2-2013 typical performance curves 0 2 4 6 8 10 12 14 16 18 20 0 100 200 300 400 500 i c = 70a t j = 25c v ce = 960v v ce = 600v v ce = 240v gate charge (nc) figure 11, gate charge v ge , gate-to-emitter voltage (v) 0 20 40 60 80 100 0 20 40 60 80 100 120 10 100 1000 0 20 40 60 80 100 120 0 1000 2000 3000 4000 5000 6000 0 25 50 75 100 125 0 2000 4000 6000 8000 10000 0 10 20 30 40 50 100 1000 10000 100000 10 30 50 70 90 110 130 150 v ce = 600v, v ge =15v, r g = 4.3? t j = 25c or 125c t d(on) i ce , collector-to-emitter current (a) figure 12, turn-on time vs collector current switching time (ns) i ce , collector-to-emitter current (a) figure 13, turn-off time vs collector current switching time (ns) r g , gate resistance () figure 15, energy loss vs gate resistance i ce , collector-to-emitter current (a) figure 14, energy loss vs collector current switching energy loss (j) t j , junction temperature (c) figure 16, swiitching energy vs junction temperature switching energy losses (j) t r t d(off) t f v ce = 600v, v ge =15v, r g = 4.3? t j = 25c t j = 125c v ce = 600v, v ge =15v, r g = 4.3? t j = 25c t j = 125c e on2 e off e on2 e off v ce = 600v, v ge =15v, i c = 70a t j = 125c switching energy loss (j) e off e on2 v ce = 600v, v ge =15v, r g = 4.3? i c = 70a 1.0e?10 1.0e?9 1.0e?8 1.0e?7 0 10 20 30 40 50 c oes c res c ies v ce , collector-to-emitter voltage (volts) figure 10, capacitance vs collector-to-emitter voltage c, capacitance (f) 1 10 100 1000 0.1 1 10 100 1000 10000 v ce , collector-to-emitter voltage figure 17, minimum switching safe operating area i c , collector current (a) 1ms 100ms 10ms .1ms .01ms downloaded from: http:///
052-6411 rev a 2-2013 APT70GR120B2_l 15.49 (.610)16.26 (.640) 5.38 (.212)6.20 (.244) 4.50 (.177) max. 19.81 (.780)20.32 (.800) 20.80 (.819)21.46 (.845) 1.65 (.065)2.13 (.084) 1.01 (.040)1.40 (.055) 5.45 (.215) bsc 2.87 (.113)3.12 (.123) 4.69 (.185)5.31 (.209) 1.49 (.059) 2.49 (.098) 2.21 (.087)2.59 (.102) 0.40 (.016)0.79 (.031) gate these dimensions are equal to the to-247 without the mounting hole. 7/22/96 changed lead ctr. to ctr. from 5.25mm to 5.45mm 1/28/98 removed mtg. hole for tmax to-247 2-plcs. 19.51 (.768)20.50 (.807) 19.81 (.780)21.39 (.842) 25.48 (1.003)26.49 (1.043) 2.29 (.090)2.69 (.106) 0.76 (.030)1.30 (.051) 3.10 (.122)3.48 (.137) 4.60 (.181)5.21 (.205) 1.80 (.071) 2.01 (.079) 2.59 (.102) 3.00 (.118) 0.48 (.019)0.84 (.033) collector emitter gate dimensions in millimeters and (inches) 2.29 (.090)2.69 (.106) revised4/03/97 5.79 (.228)6.20 (.244) 2.79 (.110)3.18 (.125) 5.45 (.215) bsc 2-plcs. dimensions in millimeters and (inches) collectoremitter collector collector t-max tm (b2) package outline to-264 (l) package outline downloaded from: http:///
APT70GR120B2_l 052-6411 rev a 2-2013 the information contained in the document (unless it is publicly available on the web without access restrictions) is proprietary and confidential information of microsemi and cannot be copied, published, uploaded, posted, transmitted, distributed or disclosed or used without the express duly signed written consent of microsemi. if the recipient of this document has entered into a disclosure agreement with microsemi, then the terms of such agreement will also apply . this document and the information co ntained herein may not be modiied, by any person other than authorized personnel of microsemi. no license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducement, estoppels or otherwise. any license under such intellectual property rights must be approved by mi crosemi in writing signed by an oficer of microsemi. microsemi reserves the right to change the coniguration, functionality and performance of its produc ts at anytime without any notice. this product has been subject to limited testing and should not be used in conjunction with life-support or other mission-critical equipment or applications. microsemi assumes no liability whatsoever, and microsemi disclaims any express or implied warranty, relating to sale and/or use of microsemi products including liability or warranties relating to itness for a particular purp ose, merchantability, or infringement of any patent, copyright or other intellectual property right. any performance speciications believed to be reliable but are not veriied and customer or user must conduct and complete all performance and other testing of this product as well as any u ser or customers inal application. user or customer shall not rely on any data and performance speciications or parameters provided by micro semi. it is the customers and users responsibility to independently determine suitability of any microsemi product and to test and verify the same. the information contained herein is provided as is, where is and with all faults, and the entire risk associated with such information is entirely with the user. mi- crosemi speciically disclaims any liability of any kind including for consequential, incidental and punitive damages as well as lost proit. the product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp downloaded from: http:///
|
